The cost to switch from gas to induction, all of it.
Appliance reviews price the range and skip the wiring. Electrician pages price the wiring and skip the range. This is the whole stack: range, 240V circuit, gas capping, and the panel question, with the rebates that apply.
Every line item on a gas-to-induction quote
Five possible line items. Two are always there, one is small, one is cheap or moderate depending on your wiring, and one hits a minority of homes hard.
| Line item | Typical cost | Notes |
|---|---|---|
| Induction range | $1,200–$3,300+ | budget to premium; tiers broken out below |
| New 240V outlet (circuit already exists) | $175–$300 | ~$220 typical |
| New dedicated 240V circuit from the panel | $250–$800+ | 30" ranges typically need 40A, 36" need 50A |
| Capping the gas line | Small plumber line item | no reliable national figure; get it on the range quote |
| Panel upgrade (15–20% of installs only) | $1,300–$3,000 | panel-only swap; full service upgrade $3,500–$4,500+ |
The $1,700 to $4,000 headline figure is a derived estimate: equipment plus circuit plus basic install, combined from the component costs above. It is not a directly surveyed market price, and it excludes the panel-upgrade minority and the gas-capping line. Still deciding whether induction is right for you at all? Start with the induction vs gas comparison, then come back for the money.
What the appliance itself costs
Three tiers, no brand hype. The middle tier is where most buyers land.
| Tier | Equipment price | What you get |
|---|---|---|
| Budget freestanding | $1,200–$2,000 | standard 30" size, four zones, the core induction experience without extras |
| Mainstream | $2,000–$3,000 | where most of the selection sits: convection ovens, bridge zones, better controls |
| Premium | $3,300+ | pro styling, 36" widths, larger capacity, higher-wattage zones |
Budget models cook on induction just as fast as premium ones; the price climbs with oven features, width, and finish, not with the fundamental technology. If the budget tier is still a stretch this year, a portable 120V single-burner induction unit costs far less, needs no wiring, and lets you test your cookware while you plan the real switch.
Where quotes diverge: getting 240V to the range
A gas range runs on a standard 120V outlet plus the gas line. A full-size induction range needs a 240V circuit: 40 amps for a typical 30-inch model, 50 amps for a 36-inch. Whether that circuit exists near your range is the single biggest variable in your quote.
| Your situation | Electrical cost | Notes |
|---|---|---|
| A 240V circuit already reaches the kitchen, you just need the outlet | $175–$300 | ~$220 typical; the cheap visit |
| No 240V near the range: new dedicated circuit run from the panel | $250–$800+ | distance and finished walls drive the top end |
| Panel can't take the new circuit: upgrade first | $1,300–$3,000+ | the 15–20% minority; see the panel section |
How to tell which row you are in before calling anyone: look behind the range. A large three- or four-prong outlet (bigger than a normal wall plug) means 240V is already there, which mostly happens when the house once had an electric range. Only a gas connector and a standard plug means you need new wiring. Then open your panel door: a double-width breaker labeled range or oven is another sign the circuit exists. If you see neither, budget for the new-circuit row and let the electrician confirm the run.
The 15 to 20 percent who pay more
Most pages bury this. Roughly 15 to 20 percent of induction installations trigger a panel upgrade, typically pre-1990 homes with less than 100-amp service. Screen yourself before you collect quotes.
new panel and breakers, existing service and meter stay
includes new meter and service entrance; many swap quotes exclude this
Those are two different jobs, and quotes that don't say which one they cover are the main reason panel prices look random. Our panel upgrade cost guide breaks down the line items and when a subpanel or load management gets you out of the upgrade entirely.
One reframe if the screen says upgrade: a bigger panel is not just a stove expense. It also unlocks the heat pump, the water heater, and the EV charger later, so price it as the first step of the bigger project. When you're ready, get panel upgrade quotes from electricians who do this work.
The small line item nobody prices
Once the gas range leaves, the gas line behind it should be capped by a plumber or gas fitter. It's a short visit, and there is no reliable national price for it, so we won't invent one. The practical advice: ask for the capping as a line item on the same quote as the range install or the electrical work, so it doesn't turn into a separate service-call minimum. Leaving the capped line in place is normal and keeps the option open if a future owner wants gas back.
There's a follow-on question worth asking while the plumber is there: is the stove the last thing in the house that burns gas? If the furnace and water heater are already electric, dropping gas service entirely means the fixed monthly meter charge goes away, which quietly improves the economics of the whole switch. That decision belongs to the bigger plan: see the whole-home electrification plan for the end state, and the retrofit sequencing guide for where the stove fits in the order of operations. Short version: the stove is usually the cheapest gas appliance to replace, so it can go almost anywhere in the sequence, but the wiring is cheapest when it rides along with other electrical work.
What HEAR covers, where it has launched
The federal Home Electrification and Appliance Rebates program rolls out state by state. The caps below apply only in states with a launched program, and only for income-eligible households.
HEAR per-measure cap · income-eligible households · launched states only
HEAR per-measure cap · covers the 240V circuit work · same eligibility
The income tiers decide how much of those caps you actually get: households under 80% of area median income can have 100% of project cost covered up to the caps, 80 to 150% AMI gets 50%, and above 150% AMI is generally not eligible. If you're in the panel-upgrade minority, HEAR also caps panel work at $4,000 under the same rules, which can change the math on the most expensive scenario on this page.
One caveat matters more than the others for this specific switch. DOE guidance issued in June 2026 eliminated HEAR rebates for fuel-switching nationally: replacing gas equipment with electric no longer qualifies, and electric appliances now qualify only for new construction or for replacing equipment that was already electric. Going from a gas range to induction is a textbook fuel switch, so that's the case this new rule targets directly. States that were already paying the induction-cooking and wiring caps under the old rules have roughly three months from June 2026 to amend, so a state marked "launched" today may still honor the old terms briefly, but that window is closing through late summer 2026.
Two more honest caveats. First, rollout: each state runs its own program on its own timeline, several have launched, many have not, and some launched programs have paused or reserved out. Second, there is no federal tax credit to fall back on here: the 25C credit never covered ranges and expired at the end of 2025 anyway. Between the rollout patchwork and the fuel-switching change, the rebate story here is unsettled and entirely state-specific, so check yours with the Rebate Matcher before you count on a dollar of it.
Gas-to-induction cost questions
How much does it cost to switch from a gas stove to induction?
A typical all-in figure is $1,700 to $4,000: the range itself ($1,200 to $3,300 and up depending on tier), the 240V electrical work ($175 to $800 and up depending on whether a circuit already exists), and basic installation. That estimate is derived by combining those component costs, not a directly surveyed market figure. It excludes the minority of homes that also need a panel upgrade, and the small plumber charge to cap the gas line.
Do I need an electrician to install an induction range?
If you are switching from gas, almost certainly yes. Gas range locations rarely have the 240V outlet an induction range requires, so an electrician has to add an outlet or run a new dedicated circuit from the panel. If you were replacing an existing electric range instead, the outlet is usually already there and delivery installers can often handle the swap.
How much does a 240V outlet for a stove cost?
If a suitable 240V circuit already exists at the range location, adding the outlet runs $175 to $300, with about $220 typical. If there is no circuit to tap, a new dedicated 240V run from the panel costs $250 to $800 or more, depending on the distance and how much finished wall is in the way.
Do I need to upgrade my panel for an induction range?
Most homes do not. Roughly 15 to 20 percent of induction installations trigger a panel upgrade, and those are typically pre-1990 homes with less than 100-amp service. If yours is one of them, a panel-only swap runs about $1,300 to $3,000, while a full service upgrade with new meter and service entrance can exceed $3,500 to $4,500. An electrician can settle the question quickly with a load calculation.
Do induction ranges need special cookware?
They need cookware with a magnetic base. Cast iron, carbon steel, enameled cast iron, and most stainless steel already qualify; plain aluminum and copper do not unless they have a bonded magnetic layer. The test costs nothing: if a fridge magnet grips the bottom of the pan, the pan works on induction.
Induction and wiring rebates open state by state. Get the alert when yours does.
Free weekly digest. Unsubscribe anytime. Privacy policy.
Some states still pay toward the stove and the wiring. Find out in two minutes.
HEAR's per-measure caps run up to $840 for induction cooking and $2,500 for the 240V work, income-eligible only, and a 2026 federal rule change is phasing out this exact fuel-switching case state by state. The Rebate Matcher shows what your state actually offers today.
Match my rebates